Safety Statement
It is the policy of aerZeal Ltd. to comply with the Safety, Health and Welfare at Work Act 2005, Construction Regulations 2013, Working at Heights Regulations 2006, Covid-19 Regulations & Guidelines 2020. To ensure as far as reasonably practicable,
the safety, health and welfare of all employees whilst at work and to provide such information and training/supervision to serve this purpose. aerZeal Ltd will also follow the Standard Operating Procedures provided by CIF.
It is the policy of this company to protect, so far as is reasonably practicable, persons not employed by this company who
may be affected by our activities.
All employees have a duty of care also under the 2005 Act and the Covid-19 Regulations and Guidelines 2020. Thus placing the responsibility to co-operate with management, to achieve a safe and healthy workplace. To take reasonable care of themselves and others and observe safe working practices.
It is the policy of this company to consult all staff and employees on matters of Safety, Health and Welfare. Employees are hereby notified of company policy and are encouraged to comply with their duties under the 2005 Act and the Covid-19 Regulations and Guidelines, by notifying the company management of identified hazards in the workplace. As such, to strive to eliminate any foreseeable hazards which may result in personal injuries, ill health, fires, security losses and or damage to property, in line with our Safety Management System.
aerZeal Ltd. are committed to continual improvement of our environmental Health and Safety performance, policy and procedures, through periodic review and monitoring with regular audits to ensure that they remain relevant and appropriate.
The success of the policy will depend on co-operation. Therefore, it is of the upmost importance that staff, subcontractors and management, understand their role in the overall arrangements made for Safety, Health and Welfare at all sites and
workplaces attended by aerZeal Ltd. It is the policy at aerZeal Ltd. to instruct all associated with the company, to
remove themselves immediately from any site or workplace, where safe working practices are not being observed, including the new Covid-19 Regulations & Guidelines.At aerZeal Ltd, we conduct continuous general risk assessment of all equipment
and activities involved in our day to day operations. All personal involved in any activities have read this safety statement.
This statement was updated on 12th June 2020 and includes consideration of Covid-19 regulations and advice.
This assessment is outlined below.
—————————————
Company policy on travelling to and from work
Company vehicle cannot be shared unless cleaned after each person uses the vehicle.
Attention to specific areas is essential. Steering wheel, gear change, door handles, light
and indicator switches and any other elements touched by hand will need to be
hygienically cleaned against Covid-19. No passengers allowed in the vehicle at any time.
If public transport is used, the company recommends the use of face masks.
Company Policy on Hand Hygiene
Hands will be washed using soap and water for two minutes, on arrival to place of work.
Hands will be washed regularly throughout the day and when leaving the place of work.
Hands must be washed each time you return to your place of work after breaks or leaving
the site temporarily during the working day.
Company policy on the wearing of face masks.
Appropriate face masks will be worn when carrying out various tasks if required, such as
doing work where there is dust or hazardous chemicals. Masks will also be worn if working
in close proximity to another worker, where the two metre safe distance cannot be
maintained, while the Covid-19 Pandemic is continuing.
Other trades
All employees need to be aware of other trades working in the same area. Both from a
Covid-19 perspective and from a general health and safety perspective. For example,
electrical cables causing a trip hazard, protruding pipe work, wet or slippery areas, work
overhead etc. Awareness is essential at all times and constant monitoring of your
surroundings.
Clean as you go Policy
All staff are trained to clean all areas of work regularly. This is to avoid the possibility of
causing an accident due to tripping over waste materials such as backing tapes. Tidiness
is essential to avoid damage to products or surfaces.Certification
All staff must keep their Safe Pass and manual handling certs up to date.
PPE
All relevant PPE must be worn before work commences. Hard hats, Hi-Vis vests, overalls,
safety boots and safety glasses must be worn at all times. Gloves, masks and hearing
protection when appropriate.
Raw Materials
The materials used by aerZeal Ltd are non hazardous.
These materials are as follows:
Intello Airtightness membrane in rolls of 1.5m x 50m
Various Airtightness tapes
Solitex external sealing membrane
Liquid primer
Aerosana Visconn Airtightness paint
Orcon sealant
Environmental Impacts
There are no environmental impacts resulting from works carried out by aerZeal Ltd.
There is a positive environmental impact resulting from the work carried out by aerZeal Ltd.
Airtightness reduces emissions and energy usage.
Site inductions
Site inductions must be carried out when arriving at new sites. This can be done by the
main contractor, owner, site safety officer, foreman. On smaller sites, where this is not
possible, each worker must make themselves aware of every aspect of Health and Safety
on the site. Location of first aid, location of nearest hospital and their contact number,
location of nearest fire station and their contact number. Identify assembly points in the
event of a fire. On isolated sites, it is always necessary to make yourself aware of the
distance to the nearest point of assistance, in case of emergency. No employee should
ever work alone or if there are no safety protocols in place.Working after hours or in low light
No work should be carried out without appropriate lighting. Awareness of and
consideration for local population when working early or late hours. Noise level should be
kept to a minimum. Planning permissions should be checked to see if out of hours work is
permitted.
Manual Handling
Manual Handling means the lifting, putting down, pushing, pulling, carrying or moving of a
load which involves risk of injury due to risk factors such as: Load is too heavy, large,
awkward or is carried away from the body. Load is lifted too high or carried too far / too
often or involves bending and / or twisting. Inadequate space, uneven floor or steps / ramps.
Current Controls Actioned
Each manual handling task is assessed (using the risk factors) and measures put in place
where needed to avoid or reduce the risks.
Risk Factors: Load is too heavy / large / awkward or carried with arms outstretched. Load
is lifted above shoulder height, lowered to floor level or carried too far. Moving the load
involves bending /twisting of body or is done more than 30 times per hour.
Task is organised to allow the use of mechanical aids (e.g. hoist, forklift, stairlift, gantry
crane, winch, goods lift, pallet truck, trolley) to avoid or reduce the need for manual handling.
Maintain the equipment in good working order and make sure staff are trained in its correct
use. Lifting equipment such as hoists and lifts must be examined every 6 or 12 months by a competent person.
Task is organised so that handling is carried out between waist and shoulder height.
Where possible heavy loads should be stored at waist height and lighter loads stored at a higher level.
Heavy, large or unwieldy loads are broken down into more manageable weights, sizes or
suitable mechanical aids / team lifts are used.
Load weight should be reduced where possible for safe handling e.g. source a 10kg bag of
material instead of 20kg. Two people or a team lift may be appropriate but mechanical
handling aids, e.g. trolleys, should be used where possible for loads above 25kg.
Work is planned to prevent handling over long distances or frequent repetitions.
Where repetitive tasks cannot be eliminated, it is good practice to rotate staff.
Efforts could be made to reduce carry distances by changing the layout of a work area or
by using simple handling aids to reduce the long carrying distances.
Bending, twisting and unstable postures are avoided.Organise the workplace: good housekeeping, clear routes, adequate space and suitable
equipment can allow the safe handling / movement of loads and prevent twisting postures.
Storing materials at waist height can reduce bending and unstable postures.
Employees receive relevant manual handling training where necessary.
The control measures put in place may still require employees to carry out some manual
handling. Employees need instruction on how to assess and lift loads safely and
instruction is recommended to be delivered by a trained manual handling instructor.
Slips, Trips & Falls on Site
Slips, trips and falls due to poor housekeeping, stairs and steps, vehicles and uneven
walkways can cause fractures, head injuries and other serious injuries to you, your
employees and / or visitors.
Current Controls Actioned
Access routes (e.g. escape routes, stairways, walkways and workingplatforms)and work
areas are kept clean and clear of materials, obstructions and trip hazards.
A minimum of 600mm width must be kept clear on all working platforms. Avoid trailing
leads e.g. use of battery operated tools, adequate number of transformers and generators.
Site is kept clean and organised.
Put systems in place for the safe delivery and storage of materials and for collecting,
storing and disposing of waste. Adequate skips and bins are provided.
Stairs and steps are clearly visible, adequately lit and are kept clear. Procedures are in
place for dealing with ice and snow (e.g. salting or gritting).
Suitable footwear is provided and worn where necessary.
- Footwear should be slip-resistant and should provide adequate support. Consult with
employees when choosing safety footwear.
Work areas and access routes are adequately lit. Safe access (e.g. stairs, ramp, scaffold,
hoist) is provided to work areas located above and below ground.
Exposed nails are removed from timber.
Protruding reinforcing bar is cut or capped.
Access to hazardous work areas is restricted.Compressed Air Tools
Use of compressed air tools may result in accidental contact or explosions which may
cause cuts, eye injuries, internal injuries and other serious injuries to you, your employees
and/or visitors.
Current Controls Actioned
Compressors and tools are kept clean and lubricated, and are used and maintained in
accordance with the manufacturer's instructions.
Air receiver, e.g. vessel containing compressed air, must have suitable safety device(s)
and correct pressure gauge fitted and a unique identification mark and the safe working
limits displayed on it. Air supply controls should not be modified.
Compressed air receiver is examined at least every 26 months by a competent person andrecords are kept.
Records: Report of examination before first use, every 26 months & after repair;
keep a register of equipment with dates of last test. Records kept at workplace/with equipment.
Suitable protective devices are fitted to the equipment and adjusted by a competent
person and kept in good condition.
Safety valves should be located so that they discharge to a safe place. These devices
should be included in a preventative maintenance programme.
Compressor and tools are regularly checked, reported defects are dealt with promptly and
unsafe equipment is taken out of use. A preventative maintenance programme should be
put in place, including checking for signs of problems. Equipment should be depressurised before maintenance.
Employees are trained in the use of compressor and air tools.
Employees should be given information about the safe operation of the equipment and
action to identify and deal with abnormal or emergency situations.
All connections are properly clamped and whip checks used to secure air-line(s) and tools.
Maintain compressed air hoses in good condition and make sure they are suitable for the tool to be used.
Anti-vibration handles and silencers are fitted to compressor / air tools.
Employees using compressed air tools should take regular breaks or be rotated between tasks.
Tool attachments (e.g. drill bits, points, spades) are maintained and kept sharp.
Pedestrians and vehicles are kept clear (e.g. the use of exclusion zone, fencing or netting,
pedestrian routes, signs), when compressed air tools are in use.Compressor is turned off and the air is released
when tools are not in use.
PPE (Personal Protective Equipment e.g. high visibility clothing, safety footwear, helmet,
gloves, eye/ear protection, suitable dust mask) is provided and worn.
Additional Controls or Information
The sharing of hand tools is forbidden. All hand tools are cleaned regularly and disinfected against Covid-19.
Construction Dust
Breathing in some construction dusts over a long period of time may result in lung
diseases such as asthma, silicosis or lung cancer.
Current Controls Actioned
Exposure to hazardous construction dusts is avoided by using safer alternatives (Avoid
stone with a high silica content, hardwood dusts, MDF etc.)
Building materials are ordered in the correct size to reduce on-site cutting.
Dust levels are kept as low as possible.
Tools and equipment which generate dust e.g. concrete / road saws / chasing equipment,
are fitted with water suppression or dust extraction systems with HEPA filter.
Wet down dusty work areas e.g. avoid dry sweeping, damping down during demolition work.
Adequate ventilation is provided and maintained.
Local extraction, doors / windows, ventilation fans, the use of temporary screens or
sheeting to minimise exposure to other persons e.g. during roadworks.
Vehicles working in dusty environments (e.g. handling construction debris, demolition etc.)
are fitted with enclosed ventilated cabs and filtered air intakes where possible.
Doors and windows of vehicles should remain closed at all times.
Employees are informed of the health risks (e.g. silicosis, asthma) associated with
hazardous construction dust(s). Inform employees to report symptoms if they develop.
Health surveillance to detect early symptoms should be provided where needed.
RPE (Respiratory Protective Equipment i.e. FFP3 Respirator Mask / P3 Filter Half Mask) is
provided and worn when dust levels cannot be lowered and employees are trained in its fitting and use.
RPE must be suitable for the dust and must fit properly (face fit) and worn correctly every
time.Hands are washed before eating, drinking and smoking.
Knives and Sharp Objects
Contact with knives and sharp objects can cause cuts, lacerations and amputations to you,
your employees and / or visitors.
Current Controls Actioned
Use of knives and sharp objects is minimised and they are stored safely (e.g. safe location,
knife block, blade retracted or housed in a holster or sheath).
Safe work practices are in place for the use, cleaning and sharpening of knives and sharp
objects and employees are trained. Training in safe cutting and use e.g. cutting away from
the body, not leaving knives / blades in areas where others may not be aware of them e.g.
in a sink or other areas.
Knives and sharp objects are checked (e.g. blade seating, blade and overall condition of
knife) before use, reported defects are dealt with promptly and unsafe equipment is taken out of use.
Knives or sharp objects used are suitable (e.g. blade size, type of blade, holder / sheath,
rounded edges, functionality and ergonomic use) for the job. Typical categories of utility
knives include bladeless cutters, concealed blades, spring loaded blade retraction, manual
blade retraction, automatic blade retraction. Blades are kept sharp and replaced as needed.
PPE (Personal Protective Equipment e.g. cut resistant gloves, aprons) is provided and worn as required.
Additional Controls or Information
The sharing of hand tools is forbidden. All hand tools are cleaned regularly and disinfected against Covid-19.
Ladder (Straight /Extension)
Use of a ladder could result in falls from height which may cause fractures, head injuries
and other serious injuries to you, your employees and / or visitors.
Current Controls Actioned
Work is only carried out from a ladder when the job is of short duration and low risk.
The work must be light, non-repetitive and should not take longer than about 30 minutes.
Consider the use of other safer equipment e.g. podium steps, mobile scaffold tower, MEWP.
Ladder is suitable (Standard EN131; Class 1 Heavy Duty & Industrial Use,Class 2 Light Trade Use.
Class 3 Domestic Use ladder must not be used for construction work) for the work to be carried out.
Ladders must be marked by the manufacturer with the relevant standard and the maximum working load.
Ladder is checked (e.g. check for splits, cracks, damaged rungs, stiles, feet, platform,
steps, and locking devices) before use, and unsafe ladders are taken out of use.
Ladders should never be painted.
Ladder is regularly inspected by a competent person and records are kept.
Equipment should be inspected at suitable intervals when it is exposed to conditions likely
to cause damage and deterioration.
Extension ladders overlap as per the manufacturer's instructions and locking devices are used.
Employees are trained in the safe use (e.g. inspection, securing etc.) of ladders.
Work is not carried out near overhead electricity lines.
Ladders must not be used close to overhead lines / there must be a safe clearance distance.
Ladder is set up on a firm level base, leaning at a suitable angle and secured (e.g. tied at
the top or bottom; footed; use of anti-slip or other stability devices) against slipping or moving.
It is recommended that the ladder is angled at 75degrees (1 in 4). Avoid side on work and
over-reaching, move the ladder as necessary.
Non-conductive (e.g. timber or fibre-glass (GRP)) ladders are used for electrical work.
Ladders used for access are tied at the top and extend 3 rungs above the landing point unless a
suitable handhold is provided.
Moving vehicles and pedestrians are kept away from ladders when in use.
3-points of contact (e.g. two hands and a foot, or two feet and a hand) are maintained at all times when using a ladder.
Tools or equipment should not be carried when going up or down a ladder. Use a tool belt
or raise tools up using a hand line.
Additional Controls or InformationThe sharing ladders is discouraged. If a ladder is used by more than one person at a time,
the ladder must be disinfected regularly against Covid-19 and the users should pay more attention to hand hygiene.
Stepladders (A-Frame)
Use of a stepladder may result in falls from height which may cause fractures, head
injuries and other serious injuries to you, your employees and/or visitors.
Current Controls Actioned
Work is only carried out from a stepladder when the job is of short duration and low risk.
The work must be light and should not take longer than 30 minutes. Consider the use of
other safer equipment e.g. podium steps, mobile scaffold towers, MEWPs.
Ladder is suitable (Standards EN131; Class 1 Heavy Duty & Industrial Use, Class 2 Light
Trade Use. Class 3 Domestic Use must not be used for construction work) for the work to be carried out.
Ladders must be marked by the manufacturer with the relevant standard and the maximum working load.
Stepladders are used as per the manufacturer's instructions.
Stepladders should not be used to support planks as part of a work platform.
Employees are trained in the correct and safe use of stepladders. Stepladders are checked
(e.g. check for splits, cracks, damaged rungs, stiles, feet, platform, steps, restraint cords /
threads and locking mechanisms) before use, reported defects are dealt with promptly and unsafe equipment
is taken out of use.
Ladders / steps should never be painted.
Stepladder is regularly inspected by a competent person and records are kept.
Equipment should be inspected at suitable intervals when it is exposed to conditions likely
to cause damage and deterioration.
Non-conductive (e.g. timber or fibre-glass) stepladders are used for electrical work.
Stepladders are set up on a firm level base facing the work activity.
- Avoid side on work and over-reaching. Reassess the location and move the stepladder as necessary.
Stepladders are never straddled and the top three steps are not used for standing.
Moving vehicles and pedestrians are kept away from stepladders when in use.
3-points of contact (e.g. two hands and a foot, or two feet and a hand) are maintained at all
times when using a stepladder.Tools or equipment should not be carried when going up or down a ladder. Use a tool belt
or raise tools up using a hand line.
Additional Controls or Information
The sharing ladders is discouraged. If a ladder is used by more than one person at a time,
the ladder must be disinfected regularly against Covid-19 and the users should pay more attention to hand hygiene.
Manually Operated Hand Tools
Contact with manually operated hand tools can cause cuts, lacerations and other serious
injuries to you, your employees and/or visitors.
Current Controls Actioned
Hand tools are checked before use, reported defects are dealt with promptly and unsafe equipment is taken out of use.
Employees are informed of the possible risks when using the hand tools. Adequate lighting is available.
Bench vice is provided and used in workshops as required (e.g. when using hacksaws, handfiles).
PPE (Personal protective equipment e.g. gloves, eye protection) is provided and worn as required.
Additional Controls or Information
The sharing of hand tools is forbidden. All hand tools are cleaned regularly and disinfected against Covid-19.
Mobile Generator
Use of a mobile generator could result in electrocution, fumes, fire or explosions which
may cause burns, suffocation or other serious injuries to you, your employees and / or visitors.
Current Controls Actioned
Generator is used, maintained and earthed in accordance with the manufacturer's instructions.
Only trained and authorised employees operate the generator, and the operator's manual is available.
Generator is operated outside, in a well ventilated area (to prevent the build up of carbon
monoxide fumes and reduce noise) and as far away as possible from work areas.Generator should be placed
away from building vents or openings, ignition sources and flammable materials.
Generator is not overloaded (power requirements should be known and should not exceed
the capacity of the generator).
Generator is fitted with an RCD (Residual Current Device). Make sure you carry out the 'Electricity' risk assessment.
Generator is checked before use (e.g. external plugs and sockets are waterproof and
circuit breakers work), reported defects are dealt with promptly and unsafe equipment is taken out of use.
External cables, connections and electrical sockets are suitable for outdoor use and are routed so as not to pose
a trip hazard.
Generator is turned off and allowed to cool before refuelling or putting into storage.
Store fuels in approved containers away from the generator and any ignition sources.
Connecting a generator to a building supply is only carried out by a competent electrician.
Always contact your electricity provider if connecting the generator to a building supply as
this could result in back feeding into utility lines which could cause electrocution. Do not
connect a generator to a socket or distribution board.
Mobile Tower Scaffold
Using a mobile tower scaffold may result in the tower overturning, persons or materials
falling or collision with vehicles which may cause fractures, head injuries and other serious
injuries to you, your employees and/or visitors.
Current Controls Actioned
Mobile tower scaffold is erected, used, dismantled and maintained in accordance with the
manufacturers instructions (make sure the manufacturers instructions are available).
Mobile tower scaffold must be erected on firm level ground, with outriggers in place and
the castors locked when in use.
Mobile tower scaffold over 2m high is only erected, modified or dismantled by employees
who have a valid CSCS (Construction Skills Certification Scheme Mobile Tower Scaffold or
Scaffolding (Basic or Advanced) card) card when carrying out construction work.
Mobile tower scaffold components (e.g. platforms, brakes, castor wheels, bracing,
outriggers, frames) are checked before use, reported defects are dealt with promptly and
unsafe equipment is taken out of use.
Mobile tower scaffold is erected, modified and dismantled using a safe method of work
(e.g. Advanced guardrail system or 3T 'Through the Trap’).Mobile tower scaffold is not erected or used close to overhead electricity lines.
Refer to the 'Code of Practice for Avoiding Danger from Overhead Electricity
Lines’.
Manufacturer's base to height (Refer to manufacturer's instructions on stabiliser and
outrigger requirements) ratio is always followed.
Mobile tower scaffold is inspected (Form GA3 must be completed and signage should be
displayed as to the status of the equipment) by a competent person before first use, at
least once a week and after any alteration or bad weather.
Mobile tower scaffolds are not used in high winds and are not overloaded.
- Refer to manufacturer's instructions as to the recommended safe working load (SWL) and wind speed limits.
Mobile tower scaffold is kept apart (e.g. barriers, banksmen) from moving vehicles and pedestrians.
Mobile tower scaffold is not moved with employees or materials anywhere on the tower.
Openings & Edges
Unprotected openings and edges may result in falls from height which may cause
fractures, head injuries or other serious injuries to you, your employees and/or visitors.
Current Controls Actioned
Measures are in place and maintained to prevent persons or materials falling from
openings and edges (e.g. open edge of a stair landing, platform, lift/service shafts,
balconies, window openings or excavation).
Work areas should be checked before work starts to make sure the measures are
adequate. Guardrails/covers should be strong and secure enough to withstand
the force of someone falling against or on them.
Edge/fall protection is inspected by a competent person before first use, at least once a
week, after alteration or bad weather and the form GA3 (Form GA3 - Report of Results of
Inspections of Work Equipment for Work at Height is available in Learn More) completed,
and appropriate signs are displayed.
Use of Scaffolding
Using scaffolding may result in scaffold collapse, persons or materials falling which could
cause fractures, head injuries, death or other serious injuries to you, your employees and/
or visitors.
Current Controls Actioned
Scaffolding is safe to use and has been erected by a competent CSCS Scaffolder ('Basic'
or 'Advanced' CSCS ticketed scaffolders are used depending on scaffold complexity).Any required alterations to the scaffolding is only carried out by a competent CSCS Scaffolder.
Scaffolding is adequately tied, braced and not overloaded (Do not overload scaffold, use
loading bays and ensure signage displaying SWL is in place).
All working platforms have guardrails and toe boards. Do not take up boards, move
guardrails or remove ties to gain access for work.
Scaffolding is checked and inspected (Scaffolding must be inspected by a competent
person before first use, at least once a week, after alteration or bad weather and the form GA3 completed).
It is the responsibility of each contractor to make sure that the scaffolding is safe for use
before starting work. Appropriate signage should be displayed as to the status of the scaffold.
Incomplete scaffolding is not used.
Designated scaffold access points and routes are used. Climbing of scaffolding is not permitted.
Materials or equipment are not thrown or dropped from scaffolding.
Scaffolding is kept clean and clear of materials.
A clear passageway of 430mm should be maintained for persons to pass between
materials and the edge of platform.
Scaffolding is not used during bad weather (e.g. high winds, frost or snow).
Vermin
Contact with vermin or their bodily fluids may result in bites or infection which could cause
serious ill health to you, your employees and / or visitors.
Current Controls Actioned
Vermin eradication programme is in place where practical.
Always use a tool or wear protective gloves when removing dead vermin.
Good housekeeping and storage (e.g. for feed, waste etc) arrangements are in place.
Floors and work surfaces should be cleaned on a regular basis using detergents
and / or disinfectants and vermin proof containers should be used for storage
where practicable.Good hygiene practices (e.g. hand washing, covering of cuts and open wounds) are in place.
Contact with stagnant water, or water that may be contaminated, is avoided.
PPE (Personal Protective Equipment e.g. gloves) is provided and worn as required.
Visiting Customer Premises
Visiting customers premises may result in slips, trips, falls, crush injuries or threatening
behaviour which may cause cuts, bruises, head injuries or other serious injuries to you and/or your employees.
Current Controls Actioned
Employees are provided with information about the purpose of the visit, the location of the
premises and any particular risks.
Employer or other relevant person is aware of the employee's planned visits (approximate duration & locations).
Company identification is provided and shown to customer on first contact.
Employees are trained not to enter any premises without prior permission from the owner/ customer.
On arrival at a customer's premises employees make their presence known at reception or
make contact with a customer representative.
Employees are trained to avoid, and to report to their manager, any dangerous situations/
issues that may affect them and reported matters are dealt with promptly.
Where threats or aggression occur employees must break away immediately and report
the incident to their immediate supervisor/service provider.
Emergency contact numbers are provided and an incident reporting procedure is in place
including follow up action.
Telephone numbers for emergency services and key personnel should be provided
and all threats of violence or harassment are to be investigated and a record kept.
The premises rules and safety signs are obeyed.
Where relevant, employees familiarise themselves with the layout of the
premises and emergency evacuation procedures.Attic Insulation (Rigid / Quilt)
Fitting of attic insulation may result in exposure to hazardous substances, working at
height and falling materials which could cause serious injuries to you, your employees or others.
Current Controls Actioned
Attic is surveyed for suitability (e.g. attic condition, loading, equipment required, asbestos,
access arrangements, electricity etc.)
Equipment (e.g. ladders, mobile tower scaffold etc.) needed to access the attic is available
and employees are trained in its use.
Attic area is adequately lit, access point is protected and a temporary walkway is provided across joists.
RPE (Respiratory Protective Equipment e.g. filtering face mask FFP3) is provided and
worn when cutting and placing insulation and employees are trained in its use.
Train employees in the fitting and use of RPE. RPE must be suited to the employee (face fit) and worn
correctly every time.
PPE (Personal Protective Equipment e.g. coveralls, gloves, glasses, ear protection) is
provided and worn as required and employees are trained in its use. Exposed skin should
be covered when handling fibreglass insulation.
Adequate rest periods are provided during warm weather. An enclosed space can
increase the risk of heat stroke or collapse from heat stress. The risk may be increased by
the wearing of personal protective equipment or by lack of ventilation.
Attic Insulation (Blown Fibre)
Pumping of blown attic insulation may result in exposure to hazardous substances, high
temperatures and working at height which could cause serious injuries to you, your employees or others.
Current Controls Actioned
Attic is surveyed for suitability (e.g. attic condition, loading, equipment required, asbestos,
access arrangements, electricity etc.)
The insulation blower and other equipment (e.g. compressor, generator) is used and
maintained in accordance with the manufacturer’s instructions.
Make sure you carry out the 'Compressed Air Tools and Mobile Generator' risk
assessments where relevant.
Employees are trained to operate the insulation blower and the operator's manual is
available.The insulation blower is inspected before use, reported defects are dealt with promptly and
unsafe equipment is taken out of use. Check pressure switch, nozzle, hopper, blowing
hose, gauges etc.
Equipment (e.g. ladders, mobile tower scaffold, scaffolding etc.) required to access the
attic is available before starting work and employees are trained in its use.
Unsuitable materials are not fed into the hopper and it is not overfilled.
Insulation blower is isolated from its power supply before clearing blockages.
Attic area is adequately lit, access point is protected and a temporary walkway is provided across joists.
RPE (e.g. filtering face mask FFP3) is provided and worn and employees are trained in its use.
Train employees in the fitting and use of RPE. RPE must be suited to the employee (face fit) and worn
correctly every time.
PPE (personal protective equipment e.g. coveralls, gloves, glasses, ear protection) is
provided and worn as required and employees are trained in its use.
Exposed skin should be covered when handling insulation. Adequate rest periods are
provided during warm weather.
An enclosed space can increase the risk of heat stroke or collapse from heat stress. The
risk may be increased by the wearing of personal protective equipment or by lack of ventilation.
Angle Grinder
Contact with an angle grinder or ejected materials can cause burns, entanglement,
fractures, lacerations, amputation and serious injuries to you, your employees and / or visitors.
Current Controls Actioned
Angle grinder is used and maintained in accordance with the manufacturer's manual and
safety guards are in place.
Employees are trained in the use of the angle grinder and the operator’s manual is available.
Employees undergoing training must be supervised until they are competent.
Abrasive wheel is mounted by a trained, competent and authorised person, is suitable for
the work and is inspected before use. The maximum speed of the spindle must be clearly
marked on the machine.Wheel speed must be compatible with the spindle speed and the maximum operating
speed of the wheel is never exceeded. Store blades as per manufacturer's instructions.
Name(s) of employees trained and authorised to mount abrasive wheels have been
recorded in the safety statement.
Sufficient clear work space is provided and area is inspected (e.g. for flammable
substances, other persons) before cutting or grinding.
Screens should be used to control debris and sparks.
Clamps are used to secure work pieces where necessary.
Adjustments are not made when wheel is in motion. Angle grinder with a voltage greater
than 110 volts is not used on a construction site or in a damp location.
Angle grinder is checked before use, reported defects are dealt with promptly and unsafe
equipment is taken out of use.
Loose clothing, dangling jewellery and unsecured long hair are avoided
when using the angle grinder.
This statement will be updated regularly and as new risks materialise or as new equipment
is made available. As this statement is updated, a copy will be made available to all parties
concerned.
13th June 2020
Signed: _____________________ Date: ____________________
Thomas Glover (Director)
Directors: Thomas Glover, Mary Glover Email: thomas@aerzeal.com Phone: 0876878928
Company Registration No: 630826. Registered Office: 51 Bracken Road, Sandyford, Dublin D18 CV48
